{"id":7538,"date":"2023-01-17T17:01:53","date_gmt":"2023-01-17T10:01:53","guid":{"rendered":"https:\/\/achisonsafety.com.vn\/?p=7538"},"modified":"2023-01-17T17:06:37","modified_gmt":"2023-01-17T10:06:37","slug":"8-maintenance-tips-for-long-lasting-power-tools","status":"publish","type":"post","link":"https:\/\/achison.com\/en\/8-maintenance-tips-for-long-lasting-power-tools\/","title":{"rendered":"8 Maintenance Tips for Long-Lasting Power Tools"},"content":{"rendered":"

Your tools are your most valuable asset. They are what make doing your job possible. Effective power tool maintenance is the key to making those tools last and protecting your investment. Most tool maintenance practices are very simple, easy habits that you can apply daily.<\/em><\/p>

Cool Down Heated Tools<\/strong><\/p>

Overworking a tool puts a lot of stress on its motor and can cause it to overheat. This mostly happens when you are trying to work through a difficult material, like drilling into concrete or sawing a very hard wood. Overheating can also occur if you run a tool too long without stopping. If your tool seems like it is getting hot, stop what you are doing and give it a break until it can cool down. This will help save you from wearing out the motor or burning out parts.<\/p>

\"\"<\/figure>

Clean Regularly<\/strong><\/p>

For your best tool maintenance, power tools should be cleaned at the end of every shift and before they are stored away for the night. You can wipe dirt and other particles from the outside casing with a good\u00a0cleaning cloth<\/a>. Compressed air is the best option to clean the particles from the tool\u2019s vents; cleaning your tool\u2019s exhaust vents with a brush could push the dirt farther into the tool and inadvertently cause more damage later.<\/p>

Lubricate<\/strong><\/p>

Lubrication is a must to keep all the moving parts on your power tools working properly. Check the tool maintenance section of your owner\u2019s manual and follow the manufacturer\u2019s instructions on how to correctly lubricate your tool\u2019s model and which lubricant to use. Keeping your tool well-lubed keeps the parts from chafing, heating and corroding.<\/p>

Sharpen Bits and Blades<\/strong><\/p>

Using old and worn-out drill bits or saw blades means you have to work your power tool even harder to get the job done. This causes extra stress on the motor which can damage parts or cause the tool to overheat with stress. Likewise, it is also important to make sure you are using the right bit for the material you are working<\/p>

Calibrate<\/strong><\/p>

Power tools are precision instruments. They use a lot of moving parts that need to remain in alignment. The tool maintenance schedule in your user\u2019s manual will outline when a tool should be recalibrated, usually after a specified amount of use hours. Most tool companies offer calibration services for their products.<\/p>

Tool Storage<\/strong><\/p>

Power tools need to be stored in a dry, clean place. Storing power tools in a moist environment can lead to problems with the electrical components and cause corrosion. This can cause safety issues or cause your tool to stop working completely. Tools also should be stored inside a\u00a0case or cabinet<\/a>\u00a0when not in use. This helps eliminate excess dust and particles getting into the tools through the vents when not in use.<\/p>

\"\"
M18 FUEL\u2122 4-1\/2″ \/ 5″ Variable Speed Braking Grinder, Slide Switch Lock-On BT<\/figcaption><\/figure><\/div>

Replace Worn Parts<\/strong><\/p>

As your tool gets used, some parts will eventually need to be replaced. One of the most common replacements is the tool\u2019s carbon brushes, which are responsible for conducting electricity through the motor. If your tool has a drive belt, like in a belt sander or some power saws, monitor it for wear and replace worn drive belts before they snap. Power cords and switch assemblies are also parts that tend to become damaged over time and are known for needing replacements.<\/p>

Battery Care<\/strong><\/p>

Lithium-ion batteries are the current standard for power tools. One of the most important factors to keeping your lithium-ion battery well maintained is to manage heat. Allowing a battery to overheat can fry it beyond repair. Store your batteries in a climate-controlled area and avoid leaving it in places where the temperature spikes (such as in the back of an enclosed truck). Do not let the battery run completely down before recharging it.<\/p>

Implementing daily maintenance routines is the best way to prevent problems with your power tools. A simple dusting can remove dirt and particles that could otherwise end up in your gears or start corroding your electrical system. Keeping your tools clean, cool and effectively oiled is a sure way to get the most out of them.<\/p>

Source: Grainger Editorial Staff<\/strong><\/p>\n\n

\n \n
\n \n
\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n <\/div>\n \n
\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n
\n \n\n
<\/div>\n <\/div>\n <\/div>\n<\/div>\n \n\n
\n \u0110\u00e1nh gi\u00e1 ngay<\/span>\n <\/div>\n <\/div>\n","protected":false},"excerpt":{"rendered":"

Your tools are your most valuable asset. They are what make doing your job possible. Effective power tool maintenance is the key to making those tools last and protecting your investment. Most tool maintenance practices are very simple, easy habits that you can apply daily. Cool Down Heated Tools Overworking a tool puts a lot…<\/p>\n","protected":false},"author":2,"featured_media":7539,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[329,191],"tags":[593,592,591,590],"class_list":["post-7538","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-safety-information","category-uncategorized","tag-cong-cu-dien","tag-dung-cu-dien","tag-may-cat","tag-may-khoan"],"acf":[],"_links":{"self":[{"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/posts\/7538"}],"collection":[{"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/comments?post=7538"}],"version-history":[{"count":0,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/posts\/7538\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/media\/7539"}],"wp:attachment":[{"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/media?parent=7538"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/categories?post=7538"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/achison.com\/en\/wp-json\/wp\/v2\/tags?post=7538"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}